The Slope page works out the slope of the ground from a surface model (DSM). It colours the ground by slope class, sums up the area in each class, and marks the ground that is steeper than your site's slope limit, for example the maximum side slope of a cell.
- Pick a surface model in the Surface models list on the left.
- Under Settings:
- Unit: show slopes in degrees (°), percent (%) or as a ratio (H:V, for example 1:3, three metres across for one metre up).
- Analysis grid: the size of the grid the slope is worked out on, 0.5 m, 1 m, 2 m or 5 m. A finer grid shows more detail, and a coarser one smooths out small bumps. 1 m is the default.
- Area: the area the figures and the table are for. Choose Whole surface model, a landfill cell, or Area drawn on the map once you have drawn one.
The page keeps your unit and grid in this browser.
When the surface model is too large for the grid you chose, the page works on a coarser grid and a chip over the view says so, for example "Read at 2 m: the model is too large for a 0.5 m grid".
The Slope limit is the steepest slope allowed on the site, for example the maximum side slope. Ground steeper than the limit is marked in red on the map and in 3D, and the figures give its area.
Site administrators set the limit. Type it, choose its unit, and click Save. Leave the field empty for no limit. The limit is the same for everyone on the site. Other users see it, but cannot change it.
- Area with a slope: the area measured.
- Mean slope: the mean slope over the area, on the chosen grid.
- Steepest: the slope of the steepest pixel.
- Steeper than the limit: the area steeper than the slope limit, and its share of the whole. It reads No limit set when the site has no limit.
The Classes list on the left gives the colour and the range of each class:
| Class |
Slope |
| Nearly flat |
under 2° |
| Gentle |
2° to 5° |
| Moderate |
5° to 10° |
| Steep |
10° to 18.4° (1:3) |
| Very steep |
18.4° to 26.6° (1:2) |
| Extreme |
over 26.6° |
The ranges follow the unit you chose.
¶ 3D and Map
The buttons over the view switch between two views:
- 3D: the surface model in 3D, coloured by slope class. Point at the surface to read its slope. See The 3D view.
- Map: the slope classes on the site map. The tools at the top of the map:
- Read: click the map to read the slope there, with the height and the coordinates.
- Area: click round an area, and double-click to close it. The figures and the table then sum up that area.
- Profile: click along a line, and double-click to end it. The Profile card under the view shows the height and the slope along the line.
- Clear: takes the drawn area and line off the map.
In the Profile chart, point along the line to see the same spot marked on the map. The line under the card gives the length of the line and how often it is sampled. Clear on the card removes the line.
¶ Area per class and Landfill cells
Area per class lists the area and share of each class for the area you chose.
When the site has more than one landfill cell, Landfill cells gives each cell's area, mean slope, steepest slope and area steeper than the limit. Click a row to choose that cell as the area.
Under Export on the left:
- GeoTIFF: the slope of each pixel, for use in a GIS. It is always in degrees, whatever unit the page shows.
- CSV: the area per class, for every area: the whole surface model, each cell, and the area you drew if there is one.
- PDF: a one-page report with the slope map, the classes and the cells.
- No surface model: add a surface model to a survey in the Surveys module. See Survey module.
- The line does not cross the surface model: draw the profile line over the area the surface model covers.
- Not a slope between flat and vertical: the limit you typed is not a valid slope. Type a value between flat and vertical, for example 2 for 1:2.